16 rims

General CMC discussion

Moderator: Al Fernandez

DBrad
Posts: 18
Joined: Sun Sep 07, 2014 7:00 am
Location: Charlotte NC

16 rims

Postby DBrad » Fri Sep 11, 2015 8:05 am

I have a set of 16 x 9 4 lug rims on my foxbody CMC car (and 2 more rims in the garage). I have taken the time to read many posts on this forum and realize I am screwed when it comes to Toyos and will one day need to convert to 17's. I'll go to 17's and Toyo's once I get my comp. license.

I am looking to pick up 2 more rims and put a set of high performance radials so I have a set of 4 to drive in the rain during the HPDE or track events.

Sorry for the long background so here's my issue, I cannot find used 16 x 9's and was thinking of going with a 16 X 8. The tires I have are 255's. Again this is only for spare tires to be used if I get caught at rain when running in HPDE. If the 16 X 8's are workable for 255's figured I'd put the 16 X9's in front since those would be under more duress and the 16 X 8's in the back.

As always your feedback is greatly appreciated.

Darren
Even a blind squirrel occassionally finds a nut!

t500hps
Posts: 129
Joined: Sat Aug 18, 2012 4:05 pm

Postby t500hps » Fri Sep 11, 2015 8:27 am

8 in wheels would work fine for rains but I'd still run a square set of equal wheels. I run 17's but have a set of 16 x 8's I wanted to use for rain wheels but they wouldn't fit over my calipers. If you ran 16 in 5 lug I have a set of wheels I'd sell CHEAP!

User avatar
TX#11CMC
Posts: 623
Joined: Thu May 19, 2005 2:14 pm
Location: Dallas, TX

Postby TX#11CMC » Sat Sep 12, 2015 9:58 am

16x8 was previously the standard wheel for CMC, with 255/50/16 tires. Not sure if there are many still out there as most switched to the 17x9's a few years ago.

When you have the time / money I would recommend doing the 5-lug conversion so you can move to the 17's. The 17's are much more available and depending on what part of the country you are in, finding take-off tires should be much easier.
-Michael Mosty
TX region #11
"Fox" driver and lovin it!!!
Texas Region - CMC Director

DBrad
Posts: 18
Joined: Sun Sep 07, 2014 7:00 am
Location: Charlotte NC

Postby DBrad » Mon Sep 14, 2015 5:39 pm

Not much luck so far finding 16 x 9's. Rather than waste time, energy and expense, will just hold off on second set and work towards the 5 lug conversion and move to 17's. I really want to get the car sorted out so I can go into the 2016 and focus on driving rather than major work on the car.

Thanks for the advice.
Even a blind squirrel occassionally finds a nut!

User avatar
BADVENM
Posts: 373
Joined: Tue Jan 08, 2008 4:00 pm
Location: Goodland, KS

Postby BADVENM » Mon Sep 14, 2015 10:16 pm

Are you planning on installing SN95 suspension pieces (front) and SN95 rear axle (I think) along with spacers to help take advantage of pushing the track width near the allowable limits? We did that a few years ago and I can tell you it (pushing the track width to the limits) made a difference in driving the car faster and harder and thus lower lap times.

We did the 5 lug disc brake conversion several years ago as well. Now running 17x9.5 wheels.
NASA Rocky Mountain - Camaro-Mustang Challenge car #8 Team Incidental Contact
3rd Place CMC - 2010 NASA National Championship
3rd Place CMC - 2015 NASA West Coast Championship PTB


Return to “General Discussion”

Who is online

Users browsing this forum: No registered users and 1 guest